Z174/b1xmax.H1xHv

Západkový tažný systém, DLC

Z174/b1xmax.H1xHv

1.2762

List s údaji o výrobku Strana v katalogu Upozornění k zabudování Mediatéka

více

Ceny a přístup do košiku umožněn pouze po registraci

Zvolení varianty výrobku

Pos10	Pos9	min.H1	F	h6	h5	h4	h3	h1	a3	a2	a1	b3	b2	l6	l5	l4	l3	l2	l1
Z31/4x12	Z26/6x20	4	16000	-	22,3	10	16	16	40	20	10	15	30,1	20	10	140	140	20	9,75
Z31/4x12	Z26/6x20	4	16000	-	22,3	10	16	16	40	20	10	15	30,1	20	10	140	140	40	9,75
Z31/4x12	Z26/6x20	4	16000	-	22,3	10	16	16	40	20	10	15	30,1	20	10	180	180	20	9,75
Z31/4x12	Z26/6x20	4	16000	-	22,3	10	16	16	40	20	10	15	30,1	20	10	180	180	70	9,75
Z31/6x16	Z26/6x20	5,5	27000	-	30,3	13	21	22	60	34	16	20	45,1	34	15	200	200	34	16,75
Z31/6x16	Z26/6x20	5,5	27000	-	30,3	13	21	22	60	34	16	20	45,1	34	15	200	200	66	16,75
Z31/6x16	Z26/6x20	5,5	27000	-	30,3	13	21	22	60	34	16	20	45,1	34	15	250	250	34	16,75
Z31/6x16	Z26/6x20	5,5	27000	-	30,3	13	21	22	60	34	16	20	45,1	34	15	250	250	109	16,75
Z31/8x18	Z26/8x24	7	48000	-	37,5	16	27	27	80	45	22	25	60,1	45	15	250	250	45	22,25
Z31/8x18	Z26/8x24	7	48000	-	37,5	16	27	27	80	45	22	25	60,1	45	15	250	250	95	22,25

b1	max.H1	Hv	Číslo výrobku
50	90	0	Z174/50x90x0
50	90	20	Z174/50x90x20
50	130	0	Z174/50x130x0
50	130	50	Z174/50x130x50
80	117	0	Z174/80x117x0
80	117	32	Z174/80x117x32
80	167	0	Z174/80x167x0
80	167	75	Z174/80x167x75
100	145	0	Z174/100x145x0
100	145	50	Z174/100x145x50

více

The HASCO-Latch locking unit Z174/... is preferably mounted on injection- and diecasting moulds requiring a second mould parting level. Advantageous applications also in the jigmaking- and machine building industry. The latch locking units allow high opening and closing speeds. The drawn plate is mechanically limited and locked in the end position. Optimum tribological properties significantly improve the service life of the moulds and thus make an important contribution to increasing the productivity of the moulds.

Improvement of the practiceproven latch locking unit
Lubricant-free production through DLC coating
Extended maintenance intervals
Due to double-sided locking system, unit can transmit enormous pulling forces
Lower wear through minimal friction coefficients
Instant or delayed pulling actions of mould plates are possible
Higher productivity due to performance safety at short machinecycle times
Coating thicknesses of only approx. 1,5 μm permit straightforward machining of the parts despite the coating